Hobbywing FlyFun-6A Bedienungsanleitung PDF herunterladen

Manual of Sensorless Brushless Speed Controller HW-SM001DUL-20130610

page 1

Size

Lipo NiMH

NiCd

L*W*H

FLYFUN-6A 6A 8A Linear

5V/0.8A

25-6

5.5g 32*12*4.5

10A

FLYFUN-10A 10A 12A Linear

5V/1A

2-4 5-12

9.5g 38*18*6

12A

FLYFUN-12A 12A 15A Linear

5V/2A

2-4 5-12

10g 38*18*7

18A

FLYFUN-18A 18A 22A Linear

5V/2A

2-4 5-12

21g 55*25*6

25A

FLYFUN-25A 25A 35A Linear

5V/2A

2-4 5-12

24g 55*25*9

30A

FLYFUN-30A 30A 40A Linear

5V/2A

2-4 5-12

26g 55*25*9

FLYFUN-40A 40A 55A Switch

5V/3A

2-6 5-18

39g 60*24*15

FLYFUN-40A-OPTO 40A 55A N/A N/A 2-6 5-18

35g 60*28*12

FLYFUN-60A 60A 80A Switch

5V/3A

2-6 5-18

63g 83*31*16

FLYFUN-60A-OPTO 60A 80A N/A N/A 2-6 5-18

60g 83*31*14

FLYFUN-80A 80A 100A Switch

5V/3A

2-6 5-18

72g 83*31*16

FLYFUN-80A-OPTO 80A 100A N/A N/A 2-6 5-18

69g 83*31*14

FLYFUN-100A 100A 120A Switch

5V/3A

2-6 5-18

76g 83*31*16

FLYFUN-100A-OPTO 100A 120A N/A N/A 2-6 5-18 73g 83*31*14

Available

Cont.

Current

Burst

Current

(>10s)

WeightBattery Cell User

Programm-able

Available

100A

Fentium Series

BEC

Mode

(Note1 )

BEC

Output

Class Model

Available

40A

60A

80A

Available

Thanks for purchasing our

Electronic Speed Controller (ESC). High power system for RC model can be very dangerous, so we

strongly suggest you read this manual carefully. In that we have no control over the correct use, installation, application, or

maintenance of our products, no liability shall be assumed nor accepted for any damages, losses or costs resulting from the use of

the product. Any claims arising from the operating, failure or malfunctioning etc. will be denied. We assume no liability for personal

injury, property damage or consequential damages resulting from our product or our workmanship. As far as is legally permitted, the

obligation to compensation is limited to the invoice amount of the affected product.

Features



Extreme low output resistance, super current endurance.



Multiple protection features: Low voltage cut-off protection / over-heat protection / throttle signal loss protection.



3 start modes: Normal / Soft / Super-Soft, compatible with fixed-wing aircraft and helicopter.



Throttle range can be configured to be compatible with all transmitters.



Smooth, linear and precise throttle response.



Separate

voltage regulator IC for microprocessor (except FLYFUN-6A and FLYFUN-10A) with good anti-jamming capability.



Maximum speed: 210000 RPM (2 poles motor), 70000 RPM (6 poles motor), 35000 RPM (12 poles motor).



The pocket-sized

Program Card

can be purchased separately for easily programming the ESC at flying field.



With a program card, user can activate the music playing function of the ESC, and totally there are 15 rhythms can be selected.

Specifications

Note1: BEC means the ³Battery Elimination Circuit´. It is a DC-DC voltage regulator to supply the receiver and other equipments

from the main battery pack. With the build-in BEC, the receiver needn¶t to be supplied with an additional battery pack.

,03257$17  7KH(6&QDPHG³[[[-xxx-2372´KDVQ¶WDEXLOW-in BEC, an UBEC (Ultimate-BEC) or an individual battery pack should

be used to supply the receiver. And an individual battery pack is needed to power the program card when programming such ESCs,

please read the user manual of the Program Card for detail information.

Wiring Diagram

Programmable Items

1. Brake Setting

Enabled / Disabled, default is Disabled

2. Battery Type

Li-xx(Li-ion or Lipo) / Ni-xx(NiMH or NiCd)ˈdefault is Li-xx.

3. Low Voltage Protection Mode(Cut-Off Mode)

Soft Cut-Off (Gradually reduce the output power) or Cut-Off (Immediately stop the

output power). Default is Soft Cut-Off.

4. Low Voltage Protection Threshold(Cut-Off Threshold)

Low / Medium / High, default is Medium.

1) For lithium batteries, the cells quantity of a battery pack is calculated automatically. Low / medium / high cutoff voltage for each

cell is: 2.85V / 3.15V / 3.3V. For example: For a 3 cells lithium pack, when ³MHGLXP´FXWRIIthreshold is set, the cut-off voltage

of this battery pack will be: 3.15*3=9.45V.

2) For nickel batteries, low / medium / high cutoff voltages are 0%/50%/65% of the startup voltage (it means the initial voltage of a

charged battery pack), and 0% means the low voltage cut-off function is disabled. For example: For a 10 cells NiMH battery,

fully charged voltage is 1.44*10=14.4VZKHQ³Medium´FXW-off threshold is chosen, the cut-off voltage will be: 14.4*50%=7.2V.

5. Startup Mode

Normal /Soft /Super-Soft ,(300ms / 6s /12s),default is Normal.

Normal is preferred for fixed-wing aircraft. Soft or Super-soft are preferred for helicopters. The acceleration of the Soft and Super-Soft

modes are slower in comparison, usually taking 6 seconds for Soft startup or 12 seconds for Super-Soft startup from zero throttle advance

to full throttle. If the throttle is closed (throttle stick moved to the bottom position, zero throttle) and opened again (throttle stick moved

upward) within 3 seconds after the initial startup, the restart-up will be temporarily changed to normal mode to get rid of the chances of a

crash caused by slow throttle response. This special design is suitable for aerobatic flight when quick throttle response is needed.

6. Timing

Low / Medium / High,( 3.75e/15e/26.25e),default is Low. Note2

Usually, low timing or medium timing is suitable for most motors. In order to get higher speed and bigger output power, please choose

High timing.

Note2: After changing the timing setting, please test your RC model on ground before taking off!

Begin To Use Your New ESC

Note3: ,QWKHIROORZLQJLQVWUXFWLRQVZHXVHWKHZRUGVRI³7RSSRVLWLRQ´DQG³%RWWRPSRVLWLRQ´WRindicate the location of the throttle

stick.

Top Position: The throttle value is 100% at this position.

Bottom Position: The throttle value is 0% at this position.

Please start the ESC in the following sequences:

1. Move throttle stick to the bottom position (zero throttle) and then switch on the transmitter.

2. Connect battery pack to the ESC, the ESC begins the self-test process, a special tone ³ 123´ emits, means the voltage of the battery

pack is in normal range, and then N ³beep´ tones emits, means the cells quantity of a lithium battery pack. Finally a long ³beep------´ tone

emits, means the self-test is OK, and the aircraft/helicopter is ready to take off.

 If nothing is happened, please check the battery pack and all the connections;

 If a special tone ³

´ emits after 2 beep tones (³beep-beep-´), means the ESC has entered the program mode, it is because the

throttle channel of your transmitter is reversed, please set it correctly;

 If the very rapid ³beep-beep-, beep-beep-´ tones emits, means the input voltage is too low or too high, please check your battery¶s

voltage.

3. ³VERY IMPORTANT!´ Because different transmitter has different throttle range, please calibrate throttle range before flying. Please

read the instruction on page 2------³Throttle Range Setting´.

Alert Tone

1. Input voltage is abnormal: The ESC begins to check the voltage when the battery pack is connected, if the voltage is not in the acceptable

range, such an alert WRQH ZLOO EH HPLWWHG ³beep-beep-, beep-beep-,beep-beep-´ (Every ³beep-beep-´ has a time interval of about 1

second. )

2. Throttle signal is abnormal: When the ESC can¶t detect the normal throttle signal, such an alert WRQHZLOOEHHPLWWHG³beep-, beep-, beep-´.

(Every ³beep-´ has a time interval of about 2 seconds)

3. Throttle stick is not in the bottom position: When the throttle stick is not in bottom (lowest) position, a very rapid alert tone will be emitted:

³beep-, beep-, beep-´. (Every ³beep-´ has a time interval of about 0.25 second.)

Protection Function

1. Start up failure protection: If the motor fails to start within 2 seconds, then the ESC will cut-off the output power. In this case, the throttle

stick MUST be moved to the bottom position (zero throttle) again to restart the motor. (Such a situation happens in the following cases:

The connection between ESC and motor is not reliable, the propeller or the motor is blocked, etc.)

2. Over-heat protection: When the temperature of the ESC is over 110 Celsius degrees, the ESC will reduce the output power.

3. Throttle signal loss protection: The ESC will reduce the output power if throttle signal is lost for 1 second, further loss for 2 seconds will

cause the output to be cut-off completely.

Program Example

6HWWLQJ³Start MRGH´WR³Super-SRIW´LHRSWLRQ #3 of the programmable item #5

1. Enter Program Mode

Switch on transmitter, move throttle stick to top position, connect battery pack to ESC, wait for 2 seconds, ³beep-beep´ tone should be

emitted. Then wait for another 5 seconds, special tone ³

´ emits, which means program mode is entered.

2. Select Programmable Items

Now you¶ll hear 8 tones in a loop. When a long ³beep------´ tone emits, move throttle stick to bottom to enter the ³Start Mode´

3. Set Item Value (Programmable Options)

³Beep-´, wait for 3 seconds; ³Beep-beep-´, wait for another 3 seconds; then you¶ll hear ³beep-beep-beep´, move throttle stick to the top

position, then a special tone ³

´ emits, that means you have set the ³Start Mode´ item to the value of ³Super-Soft´

4. Exit Program Mode

After the VSHFLDOWRQH³

´, move throttle stick to bottom within 2 seconds.

Trouble Shooting

Trouble

Possible Reason

Solution

After power on, motor does not work, no

sound is emitted

The connection between battery

pack and ESC is not correct

Check the power connection.

Replace the connectors.

After power on, motor does not work, such

an alert tone emits:

³beep-beep-, beep-beep-,beep-beep-´

(Every ³beep-beep-´ has a time interval of

about 1 second)

Input voltage is abnormal, too high

or too low.

Check the voltage of battery pack

After power on, motor does not work, such

an alert tone is emits:

³beep-, beep-, beep- ´(Every ³beep-´ has a

time interval of about 2 seconds)

Throttle signal is irregular

Check the receiver and transmitter

Check the cable of throttle channel

5S-6S Lipo

BEC Output Capability

Standard micro servos(M ax.) 5 4

2S Lipo 3S Lipo 2S - 4S Lipo

Linear Mode BEC(5V/2A)

4S Lipo

5S Lipo

Switch Mode BEC(5V/3A)

1 2

Inhaltsverzeichnis

Seite 1 - Fentium Series

Manual of Sensorless Brushless Speed Controller

Seite 2 - 2. In step 2, after hearing

Manual of Sensorless Brushless Speed Controller

Kommentare zu diesen Handbüchern

Keine Kommentare

Hobbywing FlyFun-6A Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör für die Luft Hobbywing FlyFun-6A herunter. Hobbywing FlyFun-6A User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör für die Luft Hobbywing FlyFun-6A